Buy Rod Tip Repair Kit with Glue,Complete Supplies for Freshwater & Saltwater Fishing Pole Eyelets Replacement with Rod Building Finish,Tip Guide Rings and Wrapping Thread Online at Lowest Price in Nepal B0BBT1Y4XY
The best place to mount a hook keeper is just above the reel seat on the back of the rod blank. The only problem with this location is that sometimes your line may wrap around it on a cast or when trying to pop a snagged bait undone. A micro guide works really well if you can remove the insert, so you’re left with a pretty low-profile hook keeper with a large enough diameter hole to fit any size hook. My Dad would have used Cellulose nitrate or in later years polyurethane varnish for this. You are sealing the binding from the elements, not so important with nylon thread but definitely needed with the linen button thread as damp will affect its tension. I’d got some fast set two pack epoxy glue so I decided to do some tests to see if that would work.
Repeat this process a couple times and then tie and overhand knot and cinch that down. Do that a couple times to help hold the tag end down and then snip your line off as close to the rod as you can. Add another layer of super glue to hold the line in place and seal it in a sense. Once you’ve heated the broken guide, use the razor blade to carefully slice through the rod finish. You’ll want to slice through the finish directly over where the foot is on the rod guide.
Hold the razor blade parallel to the rod and trim the end of the thread as close to the wraps as possible. Use a thread burnisher to straighten out any of your wraps, ensuring they’re tight and uniform. Once you’ve gathered the tools for the job, it’s easy to repair your broken rod in the following steps. Fishing rod guides may seem like an unimportant aspect of a fishing rod. But, once you break one, you’ll realize how vital these small components are. Each guide on a fishing rod is essential, and if a single guide fails, it renders a rod useless.
Be sure to add our email address to your email contact list to get easy order tracking details. Once you identify the type of guide you need to replace, you’ll need to figure out which size it is. Hold the new eyelet against the rod at the same spot where the old eyelet was connected. Many of you probably don’t know this about me, but I put in the work to equate to about two-thirds of a mechanical engineering degree in college. Then I did an internship for a year and realized there was no way I could spend the rest of my life inside 80 hours a week and retain my sanity. But even though I bailed on mechanical engineering, I did end up getting my masters in redneck engineering.
Recheck your alignment, at this point you can still tweak the position of the guide, or remove the binding and start again. I whipped a few test sections onto a section of bamboo cane, found some assorted pieces of plastic film to test their release properties, I mixed up some glue and tried it on one of my test sections. So I opted for the heavy polyethylene from a zip lock freezer bag. The loop wants to be somewhat longer than the length of rod you need to bind around. Secure the loop end to the rod in the middle of the guide with tape, it needs to be a low tack tape, masking tape or as I use paper surgical tape.
This helps keep the loop flat if you let it twist as you are doing the binding it makes it much harder to pull under the binding when finishing off and it looks messier. Whilst I remember the technique from helping my Dad build split cane rods in my youth,( this is the first time I’ve tried this in 30 years+) I forgot some of the detail. I thought ordinary sewing thread would be OK I was wrong it isn’t strong enough to stand being pulled back under it’s self to finish off. Once you’ve applied the finish, you’ll need to put your rod into the dryer so that the finish stays evenly distributed as it dries. A rod dryer rotates the fishing rod slowly to ensure adequate coverage with no drips or pooling.
If you’ve been around different fishing circles, you might’ve heard of the terms fishing rods and fishing poles. Carefully examine the area to ensure you’ve removed all epoxy finish and loose thread. A little extra time spent preparing the work area will make the job more seamless. He’s taught me all sorts of little life hacks, most relative to fishing.
Measure out and mix your glue, I find an old glossy magazine makes a good mixing surface and cocktail sticks good mixer/ application tools. Work a thin layer into the bindings go around a second time and check for missed spots then apply a thin but visible layer over the whole binding. Make sure there is a thin bead of glue above and below the binding and fill the void under the guide legs as well. For later ease and neatness it helps if you adjust the loop now so both sides are touching.
At this point, cut a small piece of thread and loop it over itself. Continue wrapping over the loop you’ve made until you reach the bottom of the guide ring. Take your running thread and pass it through the small loop to secure it. Wrap thread 10 to 20 times around the new eyelet and the fishing rod. Wrap with the polyethylene strip try and work out any air bubbles then secure with the tape, leave the applicator stick in the remains of the glue to check for set.
Dion Liriano is a 51-year-old American zookeeper who has retired from the business. He was once a highly successful director of the Zoo and Aquarium, but he has since hung up his gloves and moved on to other ventures. Dion's passion for animals began at a young age, when he would help his father care for their family pets. This love grew exponentially when he started working at the zoo; Dion quickly became one of the most experienced keepers in the business. He credits his success to the relationships he built with both staff and animals over the years.